What have you done to your Silverado ZR2 this week? 🛠️

[KLA]

There were 6 dip switches. I had to move 2 of them up so they’re all in the on position.

Yep! I've never had that set up. I only know info from what I have read online. For some reason I thought there were only 3 dip switches. But, either way it looks like you got it all figured out.

 

[The_Q]

Removed the Rock Sliders and steps and installed the BoostAutoParts M2 Lumasteps. I went with the sequential turn signal, puddle lights and grey hexagon step cushions. Install is very straightforward. Only one, two wire harness goes inside the cab on the passenger side. The rest of the wiring is under the hood. The motors BoostAuto uses are very heavy duty looking, so hopefully they'll hold up to use well.

 

[amateurhour]

Removed the Rock Sliders and steps and installed the BoostAutoParts M2 Lumasteps. I went with the sequential turn signal, puddle lights and grey hexagon step cushions. Install is very straightforward. Only one, two wire harness goes inside the cab on the passenger side. The rest of the wiring is under the hood. The motors BoostAuto uses are very heavy duty looking, so hopefully they'll hold up to use well.

Nice! I like the integrated lighting, never cared for amp’s lights. Any idea how they compare to the amps?

 

[csjl4life]

Finished my full cam package.
Truck has

BTR V220 full Cam Package

Long tubes

High flow cats

S&B Cold Air intake

Borla Atak Catback

Full Dyno Tune

TCM Tune

Whipple 3.0 ordered ( will forge the whole bottom end while the whipple is being installed)

Warranty is completely Void after jailbreaking the ECM And TCM. That’s always a question by people interested.

Truck made 537 to the Crank yesterday on the Dyno and that Dyno was Stingy.

July at the latest. We will smoke the TRX and the Raptor R. Guaranteed. I’ll post videos.

Let’s go ZR2 Fans.

 

[KLA]

Finished my full cam package.
Truck has

BTR V220 full Cam Package

Long tubes

High flow cats

S&B Cold Air intake

Borla Atak Catback

Full Dyno Tune

TCM Tune

Whipple 3.0 ordered ( will forge the whole bottom end while the whipple is being installed)

Warranty is completely Void after jailbreaking the ECM And TCM. That’s always a question by people interested.

Truck made 537 to the Crank yesterday on the Dyno and that Dyno was Stingy.

July at the latest. We will smoke the TRX and the Raptor R. Guaranteed. I’ll post videos.

Let’s go ZR2 Fans.

Sounds great! Can't wait to see the final results.

 

[jruck]

Ronin antenna and LasFit reverse bulbs. Boring but necessary.

 

[Busa Dave]

Did this at the ranch last weekend. Nothing that 1400.00 will not fix. Taking it in today.

 

[OC ZR2]

I'd like to buy a vowel, "O" for ouch

 

[IrishRedFish]

Just curious... What at the Ranch did That?!

 

[OC ZR2]

Let’s try to guess. Metal fence post?

 

[IrishRedFish]

That may cause a little more damage maybe?? Depending on the size of the post... its just one letter (an inch or 2 wide) and the streak is going straight up... and No damage below the letter... guess its possible.

 

[IrishRedFish]

Maybe trying to change the old chrome letters to cooler black ones and while trying to remove them slipped with the Razor Knife? IDK...

 

[OC ZR2]

hmmm
One of those funny Texas steers with square horns?

 

[OC ZR2]

Well I did add my platform while thinking about that ranch damage.

 

[IrishRedFish]

NICE!!

 

[Busa Dave]

This was my fault 101% got in a hurry as the alert came in on my phone that a Severe Dust Storm Warning was issued by the NWS to expect 0 visibility with wind gusts to 70mph. Yes, it did hit and even caused power outages in the area snapping power poles etc.

This camera shows how it happened and the wind was already blowing at 40 with gusts to 50. My back up cameras len's was covered in dust and I was not being smart trying to get close. The bottom of one of the tubes caused this.

 

[KLA]

Sorry buddy. At least it isn't too bad. Sure they will make it look like new again.

 

[Busa Dave]

Sorry buddy. At least it isn't too bad. Sure they will make it look like new again.

Yes stopped by the body shop at my dealer to drop off my Colorado Bison to fix a fiber optic cable and connector that Car Toys broke off during a upgrade to the sound system (interesting that they can repair it as the service dept said that GM does not sell the short fiber optic cable because it is wired into the main harness and connector that plugs into the module is not sold as a discrete component) and the body shop said no problem they use an outside contractor that specializes in this and it is an easy fix when you have the tools and the ability to obtain the GM specked connector which is not sold. The big ZRR2 is out of the body repair and in paint. With any luck will get it Friday!!

 

[OC ZR2]

Would have never guessed that one. Sorry to hear, hurts me from here buddy.

 

[KLA]

Yes stopped by the body shop at my dealer to drop off my Colorado Bison to fix a fiber optic cable and connector that Car Toys broke off during a upgrade to the sound system (interesting that they can repair it as the service dept said that GM does not sell the short fiber optic cable because it is wired into the main harness and connector that plugs into the module is not sold as a discrete component) and the body shop said no problem they use an outside contractor that specializes in this and it is an easy fix when you have the tools and the ability to obtain the GM specked connector which is not sold. The big ZRR2 is out of the body repair and in paint. With any luck will get it Friday!!

Did they have to replace the tailgate also? Or were they able to fix the small dent that is right on the bend in the sheet metal? A lot of times, if it is creased on a bend bad enough, they will replace the whole part other than repairing it. That's what they did with my wife's SUV. They replaced the entire rear liftgate.